Products

Application:
X
Usage:
X
PavecreteFor rubbing, smoothing, restoration, resurfacing, repairing*Dual Bonding Action
Positive mechanical bond plus
chemical bond ensures adhesion
A unique single component product, specifically designed to rub, smooth and finish vertical concrete. It will feather edge without chipping or flaking and will retain its hardness and toughness. Provides a smooth consistent light gray finish to blend with exterior cured concrete. PAVECRETE comes in a light gray, it is also available in white and sand mix
Pavecrete PlusSingle Component
Rubbing, Repairing
Resurfacing
EXTENDED WORKING TIME
USE FOR WALLS AND FLOORS
USE INSIDE AND OUT
LIGHT GRAY, BLENDS WITH CONCRETE
A versatile polymer-modified single component product. It can be used to rub, smooth and finish vertical and overhead concrete. PAVECRETE PLUS can also be as a skim underlayment or applied as a 1/4" horizontal topping for foot to car traffic. It has extended working time and an exceptional bond strength. PAVECRETE PLUS comes in a light gray, it is also available in white.
Pavecrete PrimoDual Bonding Action, Rubbing, Smoothing,
Repairing, Restoration, Resurfacing
Extra rich for smooth,
easy troweling.
Holds moisture while spreading
or rubbing
PAVECRETE PRIMO is a Portland Cement based product with graded silica aggregates and special chemical additives for bonding, hardening and moisture retention. It is formulated for smoothing, rubbing and thin coat patching applications. PAVECRETE PRIMO has a smooth, rich texture making it simple and easy to apply. After curing, it is not water sensitive, it has the setting and curing properties of regular concrete. Use of PAVECRETE PRIMO can help your project earn LEED Credits. Contact factory for details.
PatchcreteTWO COMPONENT, ACRYLIC POLYMER MODIFIED, TOPPING AND UNDERLAYMENT, OVERHEAD AND WALL REPAIRS
*Bonds to any Concrete Surface
*Light Gray to Blend with Existing Concrete
*Improved Bond and Compressive Strength
A very versatile product with an outstanding bonding characteristic. It is a two component product, a single unit includes a 45 lbs. bag of powder with a gallon of liquid polymer. It can be applied horizontally, vertically or even overhead. Horizontally, it may be applied from featheredge to 2 1/2 inch thickness (over 1/2 inch with aggregate) in one application, may be applied as a topping or underlayment. It can also be mixed to a thicker consistency and used as a trowelable repair material for wall and overhead applications. PATCHCRETE comes in light gray or white and can accept integral color or stains
Super FlowcreteINTERIOR SELF-LEVELING UNDERLAYMENT, PUMPABLE AND POURABLE, VALUE ENGINEERED,
EASY TO USE


Use as wearing surface
Use as an Underlayment
Use as Decorative flooring Suface
An interior self-levelling product with a wide variety of applications. It can be used as an underlayment or a wearing surface. SUPER FLOWCRETE has a high abrasion resistance and can be used in warehouse or light manufacturing environments with hard rubber tire forklift traffic. As it accepts integral color or stain SUPER FLOWCRETE can also be used as a decorative topping. It has a compressive strength exceeding 6000 PSI. It may be applied from featheredge to 2 inches in one application. No curing or troweling is required for SUPER FLOWCRETE. It may be used over cutback and is pumpable. SUPER FLOWCRETE utilizes P-100 Primer as its surface bonder.
FinishcreteRUBBING & SKIM COAT, SELF-DRYING, INSTALL FLOORING IN 1-2 HOURS
USE INSIDE OR OUTSIDE
USE AS A WEARING SURFACE FINISHCRETE
USE FOR VERTICAL & HORIZONTAL SURFACES
Specially designed single component product to be used in thin toppings or coverings where there is a need to quickly apply non-breathable coatings or flooring products. It can be applied indoor or outdoor, horizontal or vertical. It utilizes a self-drying technology that permits non-breathable coatings to be applied after only 1 - 2 hours. It is ideal for applying to walls prior to painting. FINISHCRETE can also be used for parging walls prior to application of waterproof membranes. It is also ideal for skim coating or quick patching floors prior to installation of epoxy, polyurethane coatings or seamless flooring systems.
P-100 PrimerPRIMER AND SURFACE BONDING, BONDING ADMIXTURE, VOC COMPLIANTBOND NEW CONCRETE TO OLD
REEMULSIFIABLE, ONE TIME ONLY
PRIMER FOR SUPER FLOWCRETE, PATCHCRETE
POWER-CRETE & CAST-PATCH
An excellent quick drying primer and surface bonder with extremely high solids count. It is a film forming, VOC compliant and will re-emulsify only one time, eliminating moisture sensitivity. P-100 is required to be used as a primer with FLOWCRETE, SUPER FLOWCRETE, CAST-PATCH and POWER-CRETE. It can also be used as a surface primer for other concrete toppings and as an integral polymer modifier for cement mortars
Flow-RockANCHORING CEMENT
NON SHRINK GROUT
Over 5,000 PSI in 1 hour
Over 10,000 PSI in a day
Over 35,000 PSI pullout strength
An extra strong, expansive anchoring cement with compressive strength exceeding 11,000 PSI and pull out strength exceeding 35,000 PSI. It may be used for a wide variety of anchoring applications. Excellent for handrail and anchor bolt applications.
Super Flow-RockEXTERIOR ANCHORING CEMENT
NON-SHRINK GROUT

FAST SETTING
HIGH COMPRESSIVE STRENGTH
OVER 40,000 LBS. PULLOUT STRENGTH
An extra strong, expansive anchoring cement designed for environments with heavy or even continuous exposure to water. SUPER FLOW-ROCK has a compressive strength exceeding 9,500 PSI and a pull out strength exceeding 40,000 lbs. It may be used for a wide variety of anchoring applications.
Plug-CreteFAST SETTING HYDRAULIC CEMENT
TO STOP WATER LEAKS IN CONCRETE
AND MASONRY

READY TO PLUG 60-90 SECONDS
STOP WATER LEAKS IMMEDIATELY
OVER 8000 PSI COMPRESSIVE STRENGTH
Stops water leaks immediately. It is ready to plug in 60-90 seconds and hard in 2-3 minutes. PLUG-CRETE reaches a compressive strength of over 8000 PSI. PLUG-CRETE is also available in 5-7 minute and 12-15 minute hardness times.
Cast-PatchFAST SETTING HYDRAULIC CEMENT
TO STOP WATER LEAKS IN CONCRETE
AND MASONRY
HIGH STRENGTH
FAST SETTING TIME
HORIZONTAL, VERTICAL AND
OVERHEAD REPAIR
A one-component repair material specifically designed to repair pre-cast concrete. CAST-PATCH is fast setting trowel grade mortar that can be shaped by sanding and shaving. CAST-PATCH reaches a Compressive Strength of 6400 psi and is suitable for a wide range of other applications.
Power-CreteRAPID SETTING TOPPING
8900 PSI COMPRESSIVE STRENGTH
READY FOR SERVICE IN 8 HOURS
SINGLE COMPONENT
STRUCTURAL REPAIR MATERIAL
USE DOWN TO 32F
A one component structural repair material. It is rapid setting, with a high early strength and an outstanding bond. POWER-CRETE can be applied from 1/2 inch to 6 inch with no aggregate needed. It can be used in horizontal repairs interior or exterior, above or below grade. POWER-CRETE utilizes P-100 Primer as its surface bonder.
----- Pavequick HR -----ROAD AND HIGHWAY REPAIR
OVER 3000 PSI IN THREE HOURS
ECONOMICAL
FAST SETTING
HIGH EARLY STRENGTH
OVER 8200 PSI IN 7 DAYS
FULL DEPTH ROAD REPAIRS
READY FOR SERVICE IN THREE HOURS
A rapid setting road and highway repair. It has a high early strength, about 2600 PSI, allowing repairs to be ready for service in two hours. PAVEQUICK HR can be used from 2 inch to FULL DEPTH and expands slightly allowing a tight fit to help reduce water penetration. PAVEQUICK HR meets or exceeds most state DOT criteria. Please contact us for current state approvals.
Lyons Premium
Non-Shrink Grout
NON-SHRINK
NON-METALLIC
HIGH STRENGTH


POURABLE/PUMPABLE
CAN BE MIXED FROM FLUID TO DRY PACK
A ready-to-use, non-shrink, non-metallic, non-corrosive grout. It attains a high strength of 11,000 PSI. Typical uses for LYONS PREMIUM NON-SHRINK GROUT include grouting under machinery base plates, structural steel to concrete, column baseplates, and general purpose concrete grouting.
acrylic-bondINTEGRAL BONDING AGENT EMULSION
HIGH SOLIDS CONTENT
EASY TO USE
IMPROVED BOND STRENGTH
IMPROVED COMPRESSIVE, FLEXURAL
AND TENSILE STRENGTH
INTERIOR OR EXTERIOR USE
Architectural quality acrylic latex emulsion for interior or exterior use as an admixture for concrete. It has a high solids content and can be used for a wide variety of concrete and masonry applications. ACRYLIC-BOND is non-reemulsifiable, it will not rewet with future exposure to water.
bondallFOR INTERIOR & EXTERIOR APPLICATIONS
INTEGRAL BONDING AGENT EMULSION
EXCELLENT SURFACE BONDER

VOC COMPLIANT
HIGH SOLIDS
RE-EMULSIFIES ONE TIME ONLY
A one time reemulsifiable liquid bonding agent and polymer modifier for concrete and masonry. It can be used interior or exterior and as a surface bonder above or below grade. BONDALL has a high solids content and is VOC compliant.
Flowcrete SLU+INTERIOR SELF-LEVELING UNDERLAYMENT
PUMPABLE AND POURABLE
VALUE ENGINEERED
EASY TO USE

*Can Be Applied Up To 3 Inches
*Can Be Applied Over Concrete & Ceramic Tile
*Allows Rapid Installation of Most Floor Coverings
A cement based, non-shrinking, self leveling floor underlayment designed for interior use. This single component product produces a smooth subfloor that will accept floor coverings in as little as 12 - 18 hours after installation. Just mix FLOWCRETE SLU+ with water, pour or pump, and it will seek its own level to produce a smooth, flat hard surface
Lyons Construction
Grout
NON-SHRINK
NON-METALLIC
HIGH STRENGTH

MEETS CRD 621
MEETS ASTM 1107
CAN BE MIXED FROM FLUID TO DRY PACK
A non-shrink, non-metallic multipurpose cement-based grout. LYONS CONSTRUCTION GROUT is formulated for a wide variety of grouting applications, from damp pack to flowable through a controlled, positive expansion.
Lyons Epoxy GroutHIGH PERFORMANCE
HIGH STRENGTH EPOXY GROUT
100% SOLIDS

Fast Curing
High early Strength
Excellent Volume Stability
Specially formulated three component, 100% solids, high strength, low exotherm epoxy grout. The system combines a high strength epoxy resin and curing agent with a specially engineered blend of graded aggregates. The special aggregate blend provides excellent flow and uniform distribution throughout the high strength epoxy matrix. The low exotherm epoxy resin allows a long work time and deep pour capabilities.
EP-1000 EPOXYBONDING ADHESIVE 100% SOLIDS BONDS CONCRETE, STEEL AND WOOD
HIGH STRENGTH
PRESSURE INJECTION
SOLVENT-FREE
A two component, low viscosity, moisture insensitive, high modulus, structural epoxy bonding adhesive and crack injection resin. EP 1000 Epoxy is 100% solids, solvent free, low odor, and high strength.
---- EP 300 ES EPOXY ----structural epoxy
bonding gel
100% solids
SOLVENT-FREE
HIGH STRENGTH
SEALS, PATCHES, ANCHORS
EP 300 FS is a two-component, moisture insensitive,
high modulus, structural epoxy bonding gel. EP 300
FS is 100% solids, solvent-free, low- odor, highstrength, and non-sag.
• Anchors bolts, dowels, and reinforcing steel
• Vertical and overhead structural bonding and
patching
• Sealing of cracks and the setting of injection
ports
• For use in concrete, block, brick, or stone
• VOC Content = 0 grams per liter
Filter is too restrictive, remove one to see products.